top of page
Search

3D Printed End of Arm Tooling: What to Print, What to Keep in Metal

Nov 3
7 min read

Yes, much of a robot's end of arm tooling (EOAT) can be 3D printed. Gripper fingers, soft jaws, part nests, vacuum-cup mounts, sensor brackets and cable guides are good candidates, because they are custom shapes made in small quantities and changed whenever the part changes. Keep the robot-side flange, tool changers, quick-change couplings and anything near welding heat or crash loads in metal or off-the-shelf hardware. 3D Infinity Printing is an FDM shop in Columbia, Missouri and St. Petersburg, Florida (both by appointment) that prints custom EOAT parts from your CAD file and ships to all 50 states.

This guide is for automation engineers, robot integrators, controls and maintenance teams, and anyone who has waited on a machined finger set to try a new part on a robot cell. It covers what to print and what to leave in metal, which materials fit which job, how to design printed fingers so they don't split at the root, and when printing is the wrong answer. For the tooling service itself, see our custom jigs, fixtures and end-of-arm tooling page.

What is end of arm tooling?

End of arm tooling (also called an end effector) is everything mounted on the robot's wrist that touches or handles the work: grippers and their fingers, vacuum cups and manifolds, magnets, tool plates, sensors and the brackets that hold them. The robot moves the tool. The EOAT decides whether the part gets picked cleanly, held square and placed in the right spot.

The robot side of the interface is standardized. ISO 9409-1 defines the circular mounting plate on the robot flange so end effectors can be exchanged and keep their orientation. Everything past that plate is usually custom to the product being handled, and that custom layer is where printing helps most.

Which EOAT parts are good candidates for 3D printing?

The best candidates are parts that are shaped around your product, built in ones and twos, and likely to change:

  • Gripper fingers and jaws. Fingers shaped to the part's profile, so it seats the same way every pick. A printed set mounts on a standard pneumatic or electric gripper body.

  • Soft jaws and contact pads. TPU pads or inserts that protect painted, polished or delicate surfaces.

  • Nests and locators. Pockets that hold a part in a known position for picking, inspection or a second operation.

  • Vacuum-cup mounts and manifolds. Brackets that place cups exactly where the part has a flat spot, with the air path built into the body.

  • Sensor, camera and light brackets. Mounts that put a proximity sensor or camera at a specific angle, which is tedious to machine.

  • Cable and hose guides. Clips and routing pieces that keep air lines and cables away from pinch points.

  • Changeover sets. A second or third finger set for a new product variant, so the cell changes over by swapping fingers rather than redesigning the tool.

Our capability in one line: jigs, fixtures and guards printed to your model, one-off geometry without tooling cost. EOAT is the same idea, mounted on a robot.

What should stay in metal?

Printing is not the right answer for every part of the tool. Keep these in metal or buy them off the shelf:

  • The robot flange adapter and tool changer. It carries the whole tool's load and the crash loads, and its bolt pattern and pilot need tight fit.

  • Quick-change couplings and the gripper body itself. Buy the actuator; print what bolts to it.

  • Anything in a weld cell or near hot parts. Spatter and radiant heat soften thermoplastics.

  • Fingers that handle sharp sheet metal or castings all day. Abrasive edges wear plastic fingers quickly. A printed finger can still prove the geometry before you machine the final set.

  • High-payload or high-speed tools where a failure is dangerous. If a dropped part could hurt someone, engineer and test the tool to that risk, whatever it is made from.

Why print EOAT instead of machining it?

  • Speed. A printed finger set needs no fixturing, programming or tool path setup for each new shape. Most parts ship 2-3 days after approval, and we quote the same day after reviewing your file.

  • Weight. The tool's weight counts against the robot's rated payload. Lighter fingers and brackets leave more of that payload for the part, and reduce the load on the wrist during fast moves.

  • Shapes that are hard to machine. Contoured fingers, internal air channels and organic nests cost little extra to print, because the printer doesn't care how complex the shape is.

  • Cheap iteration. If the first finger shape doesn't pick reliably, a revised set is another print, not another machining job.

  • No minimum order. One finger set is a normal order. So is a spare set for the maintenance crib.

The trade-off is strength and wear. A machined aluminum finger is stiffer and lasts longer against abrasion. For most light-to-moderate pick-and-place work, a well-designed printed finger in a carbon-fiber nylon is stiff enough. For heavy, abrasive or hot jobs, it is a prototype for the metal part.

Which material should printed EOAT be made from?

We print FDM only. These are the materials we usually suggest for EOAT. Availability of each material should be confirmed at quote time, except PA-CF, PPA-CF and PPS-CF, which we keep in stock.

  • PA-CF (carbon-fiber nylon). The default for gripper fingers and brackets: stiff, light and tough. A good first choice when you're not sure.

  • PPA-CF. Stiffer and more heat resistant than PA-CF, and absorbs less moisture. Use it for fingers that must hold shape in a warm cell.

  • PPS-CF. Strong chemical resistance and high heat resistance. Use it when the tool sees cutting fluids, cleaners or solvents.

  • TPU. Flexible. For soft jaws, pads and bumpers that grip without marking the part.

  • Nylon (PA6, PA12). Tough and wear-tolerant without fiber. A good choice for nests and guides that parts slide against.

  • PETG and ASA. Fine for sensor brackets, cable guides and covers in a normal-temperature cell. ASA also holds up to sunlight.

Our comparison of PA-CF, PPA-CF and PPS-CF goes deeper on the three carbon-fiber grades, and the full list is on our materials page. We don't offer printed EOAT as food-safe; for food-contact grippers, use materials your gripper supplier certifies for that use.

How should you design 3D printed gripper fingers?

FDM parts are strongest along their layers and weakest between them. Most printed fingers that fail break at the root, where the finger meets its mounting block, because the layers were stacked across the bending load. These rules prevent most problems:

  • Orient the finger so bending runs along the layers. Usually the finger lies flat on the build plate. Tell us which direction the load comes from, and we'll set orientation to match.

  • Add a generous fillet at the root. Sharp inside corners concentrate stress; a fillet spreads it.

  • Don't tap threads into plastic for parts that get re-bolted. Design for metal threaded inserts or through-bolts with nuts, so finger swaps don't strip the holes.

  • Locate with dowel pins, not just bolts. Pins set the finger's position; bolts only clamp it. Plan the pin holes undersize so they can be reamed to a press or slip fit.

  • Allow for tolerance. Our typical tolerance is ±0.2 mm. Where a fit matters, design the clearance for it, or leave stock to ream or face.

  • Build air paths in, but make them cleanable. Internal vacuum channels work well. Keep them big enough to clear with compressed air and give them an exit.

  • Add a pad pocket. A shallow pocket for a TPU pad lets you replace the wearing surface without reprinting the finger.

Our FDM design guide on wall thickness and tolerances covers clearances and minimum walls in more detail.

Printed vs machined EOAT at a glance

  • Lead time. Printed: quoted the same day, most parts ship 2-3 days after approval. Machined: depends on the shop's queue and setup.

  • Weight. Printed: lighter, especially with internal infill. Machined aluminum: heavier for the same shape.

  • Complex shapes and internal air paths. Printed: no extra setup. Machined: often several setups, or not possible.

  • Stiffness and wear. Printed: good for light-to-moderate loads; wears faster against abrasive parts. Machined: stiffer and longer wearing.

  • Heat. Printed: limited by the material; keep away from weld spatter and hot parts. Machined: much higher.

  • Changeover sets and spares. Printed: cheap to keep a spare set on the shelf. Machined: each set is a separate machining job.

When does a printed finger set make the most sense?

The strongest case is a new or changing product on an existing robot cell: the gripper body stays, and the fingers change with the part. Printing also suits proving out a new cell before committing to machined tooling, keeping a spare set ready for when a finger breaks, and replacing a worn finger whose drawing is lost. For that last case we can work from the old part; see our replacement parts service.

Printed EOAT sits next to the rest of a line's printed tooling. Our guide to 3D printed jigs, fixtures and tooling covers the fixtures and gauges that often go into the same cell.

How do you order printed EOAT?

  1. Send the CAD. STEP is best; STL, OBJ and 3MF work too. Zip the files if there are several. Include the gripper model and the part being handled.

  2. Tell us the job. Part weight, gripping direction, cycle speed, temperature and any fluids or cleaners in the cell.

  3. Get a quote the same day. We review the file, suggest material and orientation, and flag anything we'd change.

  4. Approve and receive. Most parts ship 2-3 days after approval. Larger orders are dated after file review.

No CAD? We can model fingers from a sketch, measurements or the existing part. We sign NDAs when your product or tooling is confidential.

Frequently asked questions

Can gripper fingers be 3D printed?

Yes. Gripper fingers are one of the most common 3D printed EOAT parts. A carbon-fiber nylon such as PA-CF is a typical choice. The fingers bolt to a standard gripper body, and the shape matches the part being picked.

Are 3D printed robot grippers strong enough?

For light-to-moderate pick-and-place work, usually yes, if the finger is oriented so the bending load runs along the layers and has a fillet at the root. For heavy, abrasive or hot jobs, use the printed part to prove the shape, then machine the final set.

What is the best material for 3D printed end of arm tooling?

PA-CF is the usual starting point for fingers and brackets. PPA-CF for warmer cells, PPS-CF where there are chemicals, and TPU for soft pads that must not mark the part.

Can you print the robot flange adapter plate?

We recommend keeping the flange adapter and tool changer in metal. They carry the whole tool's load and crash loads. Print what mounts past them.

Is there a minimum order for EOAT parts?

No. One finger set is a normal order, and so is a single bracket or a spare set.

Request an EOAT quote

Send your CAD file, the gripper model and a note on the part you're handling, and we'll quote the same day with a material and orientation recommendation. Upload your CAD file for an end-of-arm tooling quote, or call or text 630-485-9984.

 
 
 

Recent Posts

See All

Comments


For Questions:

Tel. 630-485-9984 Email: Joe.Stone@3Dinfinityprints.com

Text: 630.485.9984

​

Locations (we ship nationwide to all 50 states):

Florida (Tampa Bay): 160 16th St N, St. Petersburg, FL 33705 (by appointment only)

Missouri: 13 N 9th St, Columbia, MO 65201 (by appointment only)

Send us a message and we’ll get back to you shortly.

CAD files (.STL .STEP .OBJ .3MF): zip them first, then attach the .zip here.
How did you hear about us?

© 2023 by 3DInfinityPrints. 

Steve Miller Band - Fly Like An EagleSteve Miller Band
00:00 / 03:20
  • Our Etsy Storefront with over 1,000 sales
  • Instagram
  • Facebook
  • Linkedin
bottom of page